$	DeviceNet Electronic Data Sheet

[File]
	DescText   = "Single Loop Limit Controller";
	CreateDate = 06-10-2003;
	CreateTime = 14:20:00;
	ModDate    = 05-13-2005;
	ModTime    = 11:30:00;
	Revision   = 2.1;
	HomeURL    = "http://www.watlow.com";

[Device]
	VendCode    = 153;
	VendName    = "Watlow";
	ProdType    = 0;
	ProdTypeStr = "Generic Device";
	ProdCode    = 102;
	MajRev      = 2;
	MinRev      = 1;
	ProdName    = "Watlow SD6L-DS";
	Catalog     = "SD6L-XJXA-DSXX";

[IO_Info]
	Default    = 0x0001;

	PollInfo   = 0x0001, 1, 1;

	Input1=
	6, 0, 0x0001,
	"Input Image",
	6, "20 04 24 65 30 03",
	"Polled Input Image";

	Output1=
	9, 0, 0x0001,
	"Output Image",
	6, "20 04 24 64 30 03",
	"Polled Output Image";

[ParamClass]
	MaxInst     = 90;
	Descriptor  = 0x0000;
	CfgAssembly = 0;

[Params]

$ NOTE:  The following parameters MUST remain first in order for ADR to work properly!
	Param1001=
		0,
		6, "20 67 24 01 30 86",
		0x02, 0xC1, 1,
		"Comms Temperature Units",
		"",
		"Comms Temperature Units",
		0, 1, 1,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

$ Start of Setup page

	Param1100=
		0,
		6, "20 65 24 01 30 64",
		0x02, 0xC6, 1,
		"Sensor Type",
		"",
		"[ SEn] - Sensor Type",
		0, 5, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1101=
		0,
		6, "20 65 24 01 30 65",
		0x02, 0xC6, 1,
		"T/C Linearization",
		"",
		"[ Lin] - Thermocouple Linearization",
		0, 10, 1,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1102=
		0,
		6, "20 65 24 01 30 66",
		0x02, 0xC1, 1,
		"Temperature Units",
		"",
		"[ C-F] - Temperature Units",
		0, 1, 1,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1103=
		0,
		6, "20 65 24 01 30 67",
		0x02, 0xC1, 1,
		"Temperature Decimal Places",
		"",
		"[S.dEC] - Temperature Decimal Places",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1104=
		0,
		6, "20 65 24 01 30 68",
		0x02, 0xC6, 1,
		"Process Decimal Places",
		"",
		"[P.dEC] - Process Decimal Places",
		0, 3, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1105=
		0,
		6, "20 65 24 01 30 69",
		0x02, 0xC1, 1,
		"InfoSense",
		"",
		"[IS.En] - InfoSense",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1106=
		0,
		6, "20 65 24 01 30 6A",
		0x00, 0xC3, 2,
		"InfoSense 1",
		"",
		"[IS.P1] - Set sensor point 1 code.",
		0, 999, 500,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1107=
		0,
		6, "20 65 24 01 30 6B",
		0x00, 0xC3, 2,
		"InfoSense 2",
		"",
		"[IS.P2] - Set sensor point 2 code.",
		0, 999, 500,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1108=
		0,
		6, "20 65 24 01 30 6C",
		0x00, 0xC3, 2,
		"InfoSense 3",
		"",
		"[IS.P3] - Set sensor point 3 code.",
		0, 999, 500,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1109=
		0,
		6, "20 65 24 01 30 6D",
		0x00, 0xC3, 2,
		"InfoSense 4",
		"",
		"[IS.P4] - Set sensor point 4 code.",
		0, 999, 500,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1110=
		0,
		6, "20 65 24 01 30 6E",
		0x04, 0xC4, 4,
		"Process Scale Low (mA)",
		"mA",
		"[Sc.Lo] - Process Scale Low (milliamps)",
		1000, 20000, 4000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 2;

	Param1111=
		0,
		6, "20 65 24 01 30 6F",
		0x04, 0xC4, 4,
		"Process Scale Low (V)",
		"V",
		"[Sc.Lo] - Process Scale Low (volts)",
		500, 10000, 1000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 2;

	Param1112=
		0,
		6, "20 65 24 01 30 A5",
		0x04, 0xC4, 4,
		"Process Scale Low (mV)",
		"mV",
		"[Sc.Lo] - Process Scale Low (millivolts)",
		5000, 50000, 5000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 2;

	Param1113=
		0,
		6, "20 65 24 01 30 70",
		0x04, 0xC4, 4,
		"Process Scale High (mA)",
		"mA",
		"[Sc.hi] - Process Scale High (milliamps)",
		1000, 20000, 20000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 2;

	Param1114=
		0,
		6, "20 65 24 01 30 71",
		0x04, 0xC4, 4,
		"Process Scale High (V)",
		"V",
		"[Sc.hi] - Process Scale High (volts)",
		500, 10000, 5000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 2;

	Param1115=
		0,
		6, "20 65 24 01 30 A6",
		0x04, 0xC4, 4,
		"Process Scale High (mV)",
		"mV",
		"[Sc.hi] - Process Scale High (millivolts)",
		5000, 50000, 50000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 2;

	Param1116=
		0,
		6, "20 65 24 01 30 A7",
		0x04, 0xC3, 2,
		"Process Input Error Low (mA)",
		"mA",
		"[P1.LE] - Process Input Low Error (milliamps)",
		1000, 10000, 1000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 2;

	Param1117=
		0,
		6, "20 65 24 01 30 A8",
		0x04, 0xC3, 2,
		"Process Input Error Low (V)",
		"V",
		"[P1.LE] - Process Input Low Error (volts)",
		500, 5000, 500,
		1, 1000, 1, 0,
		 ,  ,  ,  , 2;

	Param1118=
		0,
		6, "20 65 24 01 30 A9",
		0x04, 0xC3, 2,
		"Process Input Error Low (mV)",
		"mV",
		"[P1.LE] - Process Input Low Error (millivolts)",
		500, 2500, 500,
		1, 100, 1, 0,
		 ,  ,  ,  , 2;

	Param1119=
		0,
		6, "20 65 24 01 30 AA",
		0x04, 0xC3, 2,
		"Process Input Error High (mA)",
		"mA",
		"[P1.HE] - Process Input High Error (milliamps)",
		10000, 20000, 20000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 2;

	Param1120=
		0,
		6, "20 65 24 01 30 AB",
		0x04, 0xC3, 2,
		"Process Input Error High (V)",
		"V",
		"[P1.HE] - Process Input High Error (volts)",
		5000, 10000, 10000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 2;

	Param1121=
		0,
		6, "20 65 24 01 30 AC",
		0x04, 0xC3, 2,
		"Process Input Error High (mV)",
		"mV",
		"[P1.HE] - Process Input High Error (millivolts)",
		2500, 5000, 5000,
		1, 100, 1, 0,
		 ,  ,  ,  , 2;

	Param1122=
		0,
		6, "20 65 24 01 30 72",
		0x04, 0xC4, 4,
		"Units Scale Low",
		"",
		"[rg.Lo] - Units Scale Low",
		-1999000, 9999000, -1999000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1123=
		0,
		6, "20 65 24 01 30 73",
		0x04, 0xC4, 4,
		"Units Scale High",
		"",
		"[rg.hi] - Units Scale High",
		-1999000, 9999000, 9999000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1124=
		0,
		6, "20 65 24 01 30 74",
		0x04, 0xC4, 4,
		"SP Low Limit (T/C)",
		"°",
		"[SP.Lo] - Set Point Low Limit for Thermocouples",
		-328000, 4200000, -200000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 1;

	Param1125=
		0,
		6, "20 65 24 01 30 75",
		0x04, 0xC4, 4,
		"SP Low Limit (RTD)",
		"°",
		"[SP.Lo] - Set Point Low Limit for RTD",
		-328000, 1472000, -200000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 1;

	Param1126=
		0,
		6, "20 65 24 01 30 76",
		0x04, 0xC4, 4,
		"SP Low Limit (Process)",
		"",
		"[SP.Lo] - Set Point Low Limit for Process",
		-1999000, 9999000, -999000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1127=
		0,
		6, "20 65 24 01 30 77",
		0x04, 0xC4, 4,
		"SP High Limit (T/C)",
		"°",
		"[SP.hi] - Set Point High Limit for Thermocouples",
		-328000, 4200000, 1371111,
		1, 1000, 1, 0,
		 ,  ,  ,  , 1;

	Param1128=
		0,
		6, "20 65 24 01 30 78",
		0x04, 0xC4, 4,
		"SP High Limit (RTD)",
		"°",
		"[SP.hi] - Set Point High Limit for RTD",
		-328000, 1472000, 800000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 1;

	Param1129=
		0,
		6, "20 65 24 01 30 79",
		0x04, 0xC4, 4,
		"SP High Limit (Process)",
		"",
		"[SP.hi] - Set Point High Limit for Process",
		-1999000, 9999000, 999000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1130=
		0,
		6, "20 66 24 01 30 64",
		0x04, 0xC4, 4,
		"Calibration Offset",
		"",
		"[ CAL] - Calibration Offset",
		-999000, 999000, 0,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1131=
		0,
		6, "20 65 24 01 30 7A",
		0x02, 0xC6, 1,
		"Input Filter",
		"",
		"[Ftr.E] - Input Filter",
		0, 3, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1132=
		0,
		6, "20 65 24 01 30 7B",
		0x04, 0xC4, 4,
		"Filter Value",
		"seconds",
		"[FLtr] - filter Value",
		0, 60000, 0,
		1, 1000, 1, 0,
		 ,  ,  ,  , 1;

	Param1133=
		0,
		6, "20 65 24 01 30 7C",
		0x12, 0xC6, 1,
		"Output 1 Function",
		"",
		"[Ot 1] - Output 1 Function",
		0, 2, 2,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1134=
		0,
		6, "20 65 24 01 30 7D",
		0x02, 0xC6, 1,
		"Output 1 Sides",
		"",
		"[LSd1] - Output 1 Limit Sides",
		0, 2, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1135=
		0,
		6, "20 65 24 01 30 7E",
		0x04, 0xC4, 4,
		"Output 1 Hysteresis",
		"",
		"[hyS1] - Limit 1 Hysteresis",
		0, 999000, 555,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1136=
		0,
		6, "20 65 24 01 30 88",
		0x02, 0xC6, 1,
		"Output 2 Function",
		"",
		"[Ot 2] - Output 2 Function",
		0, 2, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1137=
		0,
		6, "20 65 24 01 30 89",
		0x02, 0xC6, 1,
		"Output 2 Sides",
		"",
		"[LSd2] - Output 2 Sides",
		0, 2, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1138=
		0,
		6, "20 65 24 01 30 8A",
		0x04, 0xC4, 4,
		"Output 2 Hysteresis",
		"",
		"[hyS2] - Output 2 Hysteresis",
		0, 999000, 555,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1139=
		0,
		6, "20 65 24 01 30 8B",
		0x02, 0xC1, 1,
		"Output 2 Logic",
		"",
		"[Lgc2] - Output 2 Logic",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1140=
		0,
		6, "20 65 24 01 30 96",
		0x02, 0xC1, 1,
		"Alarm 2 Latching",
		"",
		"[LAt2] - Alarm 2 Latching",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1141=
		0,
		6, "20 65 24 01 30 97",
		0x02, 0xC1, 1,
		"Alarm 2 Silencing",
		"",
		"[SiL2] - Alarm 2 Silencing",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1142=
		0,
		6, "20 65 24 01 30 98",
		0x02, 0xC1, 1,
		"Alarm 2 Message",
		"",
		"[dSP2] - Alarm 2 Message",
		0, 1, 1,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1143=
		0,
		6, "20 65 24 01 30 9B",
		0x02, 0xC1, 1,
		"Input Error Latching",
		"",
		"[I.Err] - Input Error Latching",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1144=
		0,
		6, "20 65 24 01 30 99",
		0x02, 0xC6, 1,
		"Upper Display Look",
		"",
		"[UdSP] - Upper Display Look",
		0, 7, 1,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1145=
		0,
		6, "20 65 24 01 30 9A",
		0x02, 0xC6, 1,
		"Lower Display Look",
		"",
		"[LdSP] - Lower Display Look",
		0, 7, 3,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1146=
		0,
		6, "20 65 24 01 30 A1",
		0x02, 0xC6, 1,
		"Lockout",
		"",
		"[ LOC] - Lockout",
		0, 3, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

$ End of Setup page, start of Operations page

	Param1200=
		0,
		6, "20 66 24 01 30 84",
		0x04, 0xC4, 4,
		"Limit 1 Low SP",
		"",
		"[L1.Lo] - Limit 1 Low Set Point",
		-1999000, 9999000, 23333,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1201=
		0,
		6, "20 66 24 01 30 85",
		0x04, 0xC4, 4,
		"Limit 1 High SP",
		"",
		"[L1.hi] - Limit 1 High Set Point",
		-1999000, 9999000, 23888,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1202=
		0,
		6, "20 66 24 01 30 86",
		0x04, 0xC4, 4,
		"Limit / Alarm 2 Low SP",
		"",
		"[L2.Lo] / [A2.Lo] - Limit / Alarm 2 Low Set Point",
		-1999000, 9999000, 23333,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1203=
		0,
		6, "20 66 24 01 30 87",
		0x04, 0xC4, 4,
		"Limit / Alarm 2 High SP",
		"",
		"[L2.hi] / [A2.hi] - Limit / Alarm 2 High Set Point",
		-1999000, 9999000, 23888,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

$ End of Operations page, start of Programming page

	Param1300=
		0,
		6, "20 68 24 01 30 64",
		0x02, 0xC6, 1,
		"P1",
		"",
		"[  P1] - Programmable Page 1",
		0, 12, 1,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1301=
		0,
		6, "20 68 24 01 30 65",
		0x02, 0xC6, 1,
		"P2",
		"",
		"[  P2] - Programmable Page 2",
		0, 12, 2,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1302=
		0,
		6, "20 68 24 01 30 66",
		0x02, 0xC6, 1,
		"P3",
		"",
		"[  P3] - Programmable Page 3",
		0, 12, 3,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1303=
		0,
		6, "20 68 24 01 30 67",
		0x02, 0xC6, 1,
		"P4",
		"",
		"[  P4] - Programmable Page 4",
		0, 12, 4,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1304=
		0,
		6, "20 68 24 01 30 68",
		0x02, 0xC6, 1,
		"P5",
		"",
		"[  P5] - Programmable Page 5",
		0, 12, 5,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1305=
		0,
		6, "20 68 24 01 30 69",
		0x02, 0xC6, 1,
		"P6",
		"",
		"[  P6] - Programmable Page 6",
		0, 12, 6,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1306=
		0,
		6, "20 68 24 01 30 6A",
		0x02, 0xC6, 1,
		"P7",
		"",
		"[  P7] - Programmable Page 7",
		0, 12, 9,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1307=
		0,
		6, "20 68 24 01 30 6B",
		0x02, 0xC6, 1,
		"P8",
		"",
		"[  P8] - Programmable Page 8",
		0, 12, 10,     
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1308=
		0,
		6, "20 68 24 01 30 6C",
		0x02, 0xC6, 1,
		"P9",
		"",
		"[  P9] - Programmable Page 9",
		0, 12, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1309=
		0,
		6, "20 68 24 01 30 6D",
		0x02, 0xC6, 1,
		"P10",
		"",
		"[ P10] - Programmable Page 10",
		0, 12, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1310=
		0,
		6, "20 68 24 01 30 6E",
		0x02, 0xC6, 1,
		"P11",
		"",
		"[ P11] - Programmable Page 11",
		0, 12, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1311=
		0,
		6, "20 68 24 01 30 6F",
		0x02, 0xC6, 1,
		"P12",
		"",
		"[ P12] - Programmable Page 12",
		0, 12, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1312=
		0,
		6, "20 68 24 01 30 70",
		0x02, 0xC6, 1,
		"P13",
		"",
		"[ P13] - Programmable Page 13",
		0, 12, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1313=
		0,
		6, "20 68 24 01 30 71",
		0x02, 0xC6, 1,
		"P14",
		"",
		"[ P14] - Programmable Page 14",
		0, 12, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1314=
		0,
		6, "20 68 24 01 30 72",
		0x02, 0xC6, 1,
		"P15",
		"",
		"[ P15] - Programmable Page 15",
		0, 12, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1315=
		0,
		6, "20 68 24 01 30 73",
		0x02, 0xC6, 1,
		"P16",
		"",
		"[ P16] - Programmable Page 16",
		0, 12, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

$ End of Programming page, start of Factory page

	Param1400=
		0,
		6, "20 67 24 01 30 64",
		0x34, 0xC4, 4,
		"Ambient Temperature",
		"°F",
		"[AMb] - Ambient Temperature",
		-50000, 300000, 0,
		1, 1000, 1, 0,
		 ,  ,  ,  , 1;

	Param1401=
		0,
		6, "20 67 24 01 30 66",
		0x02, 0xC1, 1,
		"Restore Calibration",
		"",
		"[rESt] - Restore Factory Calibration",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1402=
		0,
		6, "20 67 24 01 30 67",
		0x02, 0xC6, 1,
		"Restore User Settings",
		"",
		"[Usr.r] - Restore User Settings",
		0, 2, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1403=
		0,
		6, "20 67 24 01 30 68",
		0x02, 0xC6, 1,
		"Save User Settings",
		"",
		"[Usr.s] - Save User Settings",
		0, 2, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1404=
		0,
		6, "20 67 24 01 30 69",
		0x02, 0xC1, 1,
		"Default Parameters",
		"",
		"[dFLt] - Default Parameters",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1405=
		0,
		6, "20 67 24 01 30 6A",
		0x12, 0xC6, 1,
		"Output 1 Type",
		"",
		"[O.ty1] - Output 1 Type",
		0, 5, 2,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1406=
		0,
		6, "20 67 24 01 30 6B",
		0x12, 0xC6, 1,
		"Output 2 Type",
		"",
		"[O.ty2] - Output 2 Type",
		0, 5, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1407=
		0,
		6, "20 67 24 01 30 6C",
		0x10, 0xC3, 2,
		"Software ID",
		"",
		"[ S.id] - Software ID",
		0, 9999, 17,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1408=
		0,
		6, "20 67 24 01 30 6F",
		0x10, 0xC3, 2,
		"Software Release Version",
		"",
		"[S.VEr] - Software Release Version",
		0, 9999, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1409=
		0,
		6, "20 67 24 01 30 70",
		0x10, 0xC3, 2,
		"Software Prototype Version",
		"",
		"[S.VEr] - Software Prototype Version",
		0, 9999, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1410=
		0,
		6, "20 67 24 01 30 6D",
		0x10, 0xC3, 2,
		"Software Build Number",
		"",
		"[S.bLd] - Software Build Number",
		0, 9999, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

$ Removed:  Unused parameter.
$	Param1411=
$		0,
$		6, "20 67 24 01 30 71",
$		0x10, 0xC3, 2,
$		"Software Branch Number",
$		"",
$		"Software Branch Number",
$		0, 9999, 0,
$		 ,  ,  ,  ,
$		 ,  ,  ,  ,  ;

	Param1412=
		0,
		6, "20 67 24 01 30 6E",
		0x10, 0xC4, 4,
		"Serial Number",
		"",
		"[ Sn-], [ Sn_] - Serial Number",
		0, 99999999, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

$ Removed:  Unused parameter.
$	Param1413=
$		0,
$		6, "20 67 24 01 30 87",
$		0x10, 0xC3, 2,
$		"Date Code",
$		"",
$		"Date Code (yy/ww)",
$		0, 9999, 0,
$		 ,  ,  ,  ,
$		 ,  ,  ,  ,  ;

$ End of Factory page, start of Home page

	Param1500=
		0,
		6, "20 64 24 01 30 64",
		0x34, 0xC4, 4,
		"PV",
		"",
		"Process Value",
		-1999000, 9999999, 0,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1501=
		0,
		6, "20 64 24 01 30 66",
		0x34, 0xC4, 4,
		"Filtered PV",
		"",
		"Filtered Process Value",
		-1999000, 9999999, 0,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

$ Removed:  Same as Param1201
$	Param1502=
$		0,
$		6, "20 64 24 01 30 65",
$		0x04, 0xC4, 4,
$		"Limit 1 High SP",
$		"",
$		"[L1.hi] - Limit 1 High Set Point",
$		-1999000, 9999000, 24000,
$		1, 1000, 1, 0,
$		 ,  ,  ,  , 3;

	Param1503=
		0,
		6, "20 64 24 01 30 6A",
		0x30, 0xC3, 2,
		"Input Error",
		"",
		"[Er.In] - Input Error",
		0, 19999, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1504=
		0,
		6, "20 64 24 01 30 68",
		0x32, 0xC1, 1,
		"Limit 1 Low Status",
		"",
		"[L1.Lo] - Limit Low 1 Status",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1505=
		0,
		6, "20 64 24 01 30 69",
		0x32, 0xC1, 1,
		"Limit 1 High Status",
		"",
		"[L1.hi] - Limit High 1 Status",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1506=
		0,
		6, "20 64 24 01 30 6B",
		0x32, 0xC1, 1,
		"Limit / Alarm 2 Low Status",
		"",
		"[L2.Lo] / [A2.Lo] - Limit / Alarm Low 2 Status",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1507=
		0,
		6, "20 64 24 01 30 6C",
		0x32, 0xC1, 1,
		"Limit / Alarm 2 High Status",
		"",
		"[L2.hi] / [A2.hi] - Limit / Alarm High 2 Status",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1508=
		0,
		6, "20 65 24 01 30 A2",
		0x02, 0xC1, 1,
		"Alarm 1 ACK",
		"",
		"Alarm 1 Acknowledge",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1509=
		0,
		6, "20 65 24 01 30 A3",
		0x02, 0xC1, 1,
		"Alarm 2 ACK",
		"",
		"Alarm 2 Acknowledge",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

$ End of Home page

$ NOTE:  The following parameters MUST remain last in order for ADR to work properly!
	Param1999=
		0,
		6, "20 67 24 01 30 85",
		0x02, 0xC1, 1,
		"Non-Volatile Writes",
		"",
		"Non-Volatile Writes",
		0, 1, 1,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

[EnumPar]

$ NOTE:  The following parameters MUST remain first in order for ADR to work properly!
	Param1001=
		"°F",
		"°C";

$ Start of Setup page

	Param1100=
		"T/C",
		"RTD",
		"mA",
		"volts",
		"Reserved",
		"mV";

	Param1101=
		"J",
		"K",
		"T",
		"E",
		"N",
		"C",
		"D",
		"PTII",
		"R",
		"S",
		"B";

	Param1102=
		"°F",
		"°C";

	Param1103=
		"0",
		"0.0";

	Param1104=
		"0",
		"0.0",
		"0.00",
		"0.000";

	Param1105=
		"No",
		"Yes";

	Param1131=
		"Off",
		"Filter Display",
		"Filter Input",
		"Filter Both";

	Param1133=
		"Off",
		"Process Alarm",
		"Limit";

	Param1134=
		"Both",
		"High Side",
		"Low Side";

	Param1136=
		"Off",
		"Process Alarm",
		"Limit";

	Param1137=
		"Both",
		"High Side",
		"Low Side";

	Param1139=
		"Closed",
		"Open";

	Param1140=
		"Off",
		"On";

	Param1141=
		"No Silencing",
		"Silencing";

	Param1142=
		"No Message",
		"Message";

	Param1143=
		"Off",
		"On";

	Param1144=
		"None",
		"Process Value",
		"Limit 1 Low Set Point",
		"Limit 1 High Set Point",
		"Limit 2 Low Set Point",
		"Limit 2 High Set Point",
		"Alarm 2 Low Set Point",
		"Alarm 2 High Set Point";

	Param1145=
		"None",
		"Process Value",
		"Limit 1 Low Set Point",
		"Limit 1 High Set Point",
		"Limit 2 Low Set Point",
		"Limit 2 High Set Point",
		"Alarm 2 Low Set Point",
		"Alarm 2 High Set Point";

	Param1146=
		"0 - No Lockout",
		"1 - Programming & Setup Page",
		"2 - Programming & Setup Page, Limit SPs Only",
		"3 - Full Lockout";

$ End of Setup page, start of Operations page

$ End of Operations page, start of Programming page

	Param1300=
		"None",
		"Limit 1 Low SP",
		"Limit 1 High SP",
		"Limit 2 Low SP",
		"Limit 2 High SP",
		"Alarm 2 Low SP",
		"Alarm 2 High SP",
		"Output 1 Hysteresis",
		"Output 2 Hysteresis",
		"MAC ID",
		"Baud Rate",
		"Temperature Units",
		"Calibration Offset";

	Param1301=
		"None",
		"Limit 1 Low SP",
		"Limit 1 High SP",
		"Limit 2 Low SP",
		"Limit 2 High SP",
		"Alarm 2 Low SP",
		"Alarm 2 High SP",
		"Output 1 Hysteresis",
		"Output 2 Hysteresis",
		"MAC ID",
		"Baud Rate",
		"Temperature Units",
		"Calibration Offset";

	Param1302=
		"None",
		"Limit 1 Low SP",
		"Limit 1 High SP",
		"Limit 2 Low SP",
		"Limit 2 High SP",
		"Alarm 2 Low SP",
		"Alarm 2 High SP",
		"Output 1 Hysteresis",
		"Output 2 Hysteresis",
		"MAC ID",
		"Baud Rate",
		"Temperature Units",
		"Calibration Offset";

	Param1303=
		"None",
		"Limit 1 Low SP",
		"Limit 1 High SP",
		"Limit 2 Low SP",
		"Limit 2 High SP",
		"Alarm 2 Low SP",
		"Alarm 2 High SP",
		"Output 1 Hysteresis",
		"Output 2 Hysteresis",
		"MAC ID",
		"Baud Rate",
		"Temperature Units",
		"Calibration Offset";

	Param1304=
		"None",
		"Limit 1 Low SP",
		"Limit 1 High SP",
		"Limit 2 Low SP",
		"Limit 2 High SP",
		"Alarm 2 Low SP",
		"Alarm 2 High SP",
		"Output 1 Hysteresis",
		"Output 2 Hysteresis",
		"MAC ID",
		"Baud Rate",
		"Temperature Units",
		"Calibration Offset";

	Param1305=
		"None",
		"Limit 1 Low SP",
		"Limit 1 High SP",
		"Limit 2 Low SP",
		"Limit 2 High SP",
		"Alarm 2 Low SP",
		"Alarm 2 High SP",
		"Output 1 Hysteresis",
		"Output 2 Hysteresis",
		"MAC ID",
		"Baud Rate",
		"Temperature Units",
		"Calibration Offset";

	Param1306=
		"None",
		"Limit 1 Low SP",
		"Limit 1 High SP",
		"Limit 2 Low SP",
		"Limit 2 High SP",
		"Alarm 2 Low SP",
		"Alarm 2 High SP",
		"Output 1 Hysteresis",
		"Output 2 Hysteresis",
		"MAC ID",
		"Baud Rate",
		"Temperature Units",
		"Calibration Offset";

	Param1307=
		"None",
		"Limit 1 Low SP",
		"Limit 1 High SP",
		"Limit 2 Low SP",
		"Limit 2 High SP",
		"Alarm 2 Low SP",
		"Alarm 2 High SP",
		"Output 1 Hysteresis",
		"Output 2 Hysteresis",
		"MAC ID",
		"Baud Rate",
		"Temperature Units",
		"Calibration Offset";

	Param1308=
		"None",
		"Limit 1 Low SP",
		"Limit 1 High SP",
		"Limit 2 Low SP",
		"Limit 2 High SP",
		"Alarm 2 Low SP",
		"Alarm 2 High SP",
		"Output 1 Hysteresis",
		"Output 2 Hysteresis",
		"MAC ID",
		"Baud Rate",
		"Temperature Units",
		"Calibration Offset";

	Param1309=
		"None",
		"Limit 1 Low SP",
		"Limit 1 High SP",
		"Limit 2 Low SP",
		"Limit 2 High SP",
		"Alarm 2 Low SP",
		"Alarm 2 High SP",
		"Output 1 Hysteresis",
		"Output 2 Hysteresis",
		"MAC ID",
		"Baud Rate",
		"Temperature Units",
		"Calibration Offset";

	Param1310=
		"None",
		"Limit 1 Low SP",
		"Limit 1 High SP",
		"Limit 2 Low SP",
		"Limit 2 High SP",
		"Alarm 2 Low SP",
		"Alarm 2 High SP",
		"Output 1 Hysteresis",
		"Output 2 Hysteresis",
		"MAC ID",
		"Baud Rate",
		"Temperature Units",
		"Calibration Offset";

	Param1311=
		"None",
		"Limit 1 Low SP",
		"Limit 1 High SP",
		"Limit 2 Low SP",
		"Limit 2 High SP",
		"Alarm 2 Low SP",
		"Alarm 2 High SP",
		"Output 1 Hysteresis",
		"Output 2 Hysteresis",
		"MAC ID",
		"Baud Rate",
		"Temperature Units",
		"Calibration Offset";

	Param1312=
		"None",
		"Limit 1 Low SP",
		"Limit 1 High SP",
		"Limit 2 Low SP",
		"Limit 2 High SP",
		"Alarm 2 Low SP",
		"Alarm 2 High SP",
		"Output 1 Hysteresis",
		"Output 2 Hysteresis",
		"MAC ID",
		"Baud Rate",
		"Temperature Units",
		"Calibration Offset";

	Param1313=
		"None",
		"Limit 1 Low SP",
		"Limit 1 High SP",
		"Limit 2 Low SP",
		"Limit 2 High SP",
		"Alarm 2 Low SP",
		"Alarm 2 High SP",
		"Output 1 Hysteresis",
		"Output 2 Hysteresis",
		"MAC ID",
		"Baud Rate",
		"Temperature Units",
		"Calibration Offset";

	Param1314=
		"None",
		"Limit 1 Low SP",
		"Limit 1 High SP",
		"Limit 2 Low SP",
		"Limit 2 High SP",
		"Alarm 2 Low SP",
		"Alarm 2 High SP",
		"Output 1 Hysteresis",
		"Output 2 Hysteresis",
		"MAC ID",
		"Baud Rate",
		"Temperature Units",
		"Calibration Offset";

	Param1315=
		"None",
		"Limit 1 Low SP",
		"Limit 1 High SP",
		"Limit 2 Low SP",
		"Limit 2 High SP",
		"Alarm 2 Low SP",
		"Alarm 2 High SP",
		"Output 1 Hysteresis",
		"Output 2 Hysteresis",
		"MAC ID",
		"Baud Rate",
		"Temperature Units",
		"Calibration Offset";

$ End of Programming page, start of Factory page

	Param1401=
		"No",
		"Yes";

	Param1402=
		"No",
		"Set 1",
		"Set 2";

	Param1403=
		"No",
		"Set 1",
		"Set 2";

	Param1404=
		"No",
		"Yes";

	Param1405=
		"None",
		"DC / Open Collector",
		"Mechanical Relay",
		"Solid-State Relay",
		"Process",
		"Communications";

	Param1406=
		"None",
		"DC / Open Collector",
		"Mechanical Relay",
		"Solid-State Relay",
		"Process",
		"Communications";

$ End of Factory page, start of Home page

	Param1504=
		"None",
		"Limit";

	Param1505=
		"None",
		"Limit";

	Param1506=
		"None",
		"Limit/Alarm";

	Param1507=
		"None",
		"Limit/Alarm";

	Param1508=
		"No",
		"Yes";

	Param1509=
		"No",
		"Yes";

$ End of Home page

$ NOTE:  The following parameters MUST remain last in order for ADR to work properly!
	Param1999=
		"Disable",
		"Enable";

[Groups]

	Group1=
		"Home Page", 9,
		1500, 1501,       1503, 1504, 1505, 1506, 1507, 1508, 1509;

	Group2=
		"Operations Page", 4,
		1200, 1201, 1202, 1203;

	Group3=
		"Setup Page", 47,
		1100, 1101, 1102, 1103, 1104, 1105, 1106, 1107, 1108, 1109,
		1110, 1111, 1112, 1113, 1114, 1115, 1116, 1117, 1118, 1119,
		1120, 1121, 1122, 1123, 1124, 1125, 1126, 1127, 1128, 1129,
		1130, 1131, 1132, 1133, 1134, 1135, 1136, 1137, 1138, 1139,
		1140, 1141, 1142, 1143, 1144, 1145, 1146;

	Group4=
		"Programming Page", 16,
		1300, 1301, 1302, 1303, 1304, 1305, 1306, 1307, 1308, 1309,
		1310, 1311, 1312, 1313, 1314, 1315;

	Group5=
		"Factory Page", 12,
		1400, 1401, 1402, 1403, 1404, 1405, 1406, 1407, 1408, 1409,
		1410,       1412;

	Group6=
		"Non User-Interface", 2,
		1001, 1999;