$	DeviceNet Electronic Data Sheet

[File]
	DescText   = "Single Loop PID Controller";
	CreateDate = 03-03-2003;
	CreateTime = 14:30:00;
	ModDate    = 02-18-2005;
	ModTime    = 11:30:00;
	Revision   = 2.1;

[Device]
	VendCode    = 153;
	VendName    = "Watlow";
	ProdType    = 0;
	ProdTypeStr = "Generic Device";
	ProdCode    = 100;
	MajRev      = 2;
	MinRev      = 1;
	ProdName    = "Watlow SD6C-DS";
	Catalog     = "SD6C-XXXA-DSXX";

[IO_Info]
	Default    = 0x0001;

	PollInfo   = 0x0001, 1, 1;

	Input1=
	7, 0, 0x0001,
	"Input Image",
	6, "20 04 24 65 30 03",
	"Polled Input Image";

	Output1=
	5, 0, 0x0001,
	"Output Image",
	6, "20 04 24 64 30 03",
	"Polled Output Image";

[ParamClass]
	MaxInst     = 155;
	Descriptor  = 0x0000;
	CfgAssembly = 0;

[Params]

$ NOTE:  The following parameters MUST remain first in order for ADR to work properly!
	Param1001=
		0,
		6, "20 67 24 01 30 86",
		0x02, 0xC1, 1,
		"Comms Temperature Units",
		"",
		"Comms Temperature Units",
		0, 1, 1,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

$ Start of Setup page

	Param1100=
		0,
		6, "20 65 24 01 30 64",
		0x02, 0xC6, 1,
		"Sensor Type",
		"",
		"[ SEn] - Sensor Type",
		0, 5, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1101=
		0,
		6, "20 65 24 01 30 65",
		0x02, 0xC6, 1,
		"T/C Linearization",
		"",
		"[ Lin] - Thermocouple Linearization",
		0, 10, 1,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1102=
		0,
		6, "20 65 24 01 30 66",
		0x02, 0xC1, 1,
		"Temperature Units",
		"",
		"[ C-F] - Temperature Units",
		0, 1, 1,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1103=
		0,
		6, "20 65 24 01 30 67",
		0x02, 0xC1, 1,
		"Temperature Decimal Places",
		"",
		"[S.dEC] - Temperature Decimal Places",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1104=
		0,
		6, "20 65 24 01 30 68",
		0x02, 0xC6, 1,
		"Process Decimal Places",
		"",
		"[P.dEC] - Process Decimal Places",
		0, 3, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1105=
		0,
		6, "20 65 24 01 30 69",
		0x02, 0xC1, 1,
		"InfoSense",
		"",
		"[IS.En] - InfoSense",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1106=
		0,
		6, "20 65 24 01 30 6A",
		0x00, 0xC7, 2,
		"InfoSense 1",
		"",
		"[IS.P1] - Set sensor point 1 code.",
		0, 999, 500,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1107=
		0,
		6, "20 65 24 01 30 6B",
		0x00, 0xC7, 2,
		"InfoSense 2",
		"",
		"[IS.P2] - Set sensor point 2 code.",
		0, 999, 500,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1108=
		0,
		6, "20 65 24 01 30 6C",
		0x00, 0xC7, 2,
		"InfoSense 3",
		"",
		"[IS.P3] - Set sensor point 3 code.",
		0, 999, 500,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1109=
		0,
		6, "20 65 24 01 30 6D",
		0x00, 0xC7, 2,
		"InfoSense 4",
		"",
		"[IS.P4] - Set sensor point 4 code.",
		0, 999, 500,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1110=
		0,
		6, "20 65 24 01 30 6E",
		0x04, 0xC8, 4,
		"Process Scale Low (mA)",
		"mA",
		"[Sc.Lo] - Process Scale Low (milliamps)",
		0, 20000, 4000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 2;

	Param1111=
		0,
		6, "20 65 24 01 30 6F",
		0x04, 0xC8, 4,
		"Process Scale Low (V)",
		"V",
		"[Sc.Lo] - Process Scale Low (volts)",
		0, 10000, 0,
		1, 1000, 1, 0,
		 ,  ,  ,  , 2;

	Param1112=
		0,
		6, "20 65 24 01 30 A5",
		0x04, 0xC8, 4,
		"Process Scale Low (mV)",
		"mV",
		"[Sc.Lo] - Process Scale Low (millivolts)",
		0, 50000, 0,
		1, 1000, 1, 0,
		 ,  ,  ,  , 2;

	Param1113=
		0,
		6, "20 65 24 01 30 70",
		0x04, 0xC8, 4,
		"Process Scale High (mA)",
		"mA",
		"[Sc.hi] - Process Scale High (milliamps)",
		0, 20000, 20000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 2;

	Param1114=
		0,
		6, "20 65 24 01 30 71",
		0x04, 0xC8, 4,
		"Process Scale High (V)",
		"V",
		"[Sc.hi] - Process Scale High (volts)",
		0, 10000, 5000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 2;

	Param1115=
		0,
		6, "20 65 24 01 30 A6",
		0x04, 0xC8, 4,
		"Process Scale High (mV)",
		"mV",
		"[Sc.hi] - Process Scale High (millivolts)",
		0, 50000, 50000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 2;

	Param1116=
		0,
		6, "20 65 24 01 30 A7",
		0x04, 0xC3, 2,
		"Process Input Error Low (mA)",
		"mA",
		"[P1.LE] - Process Input Low Error (milliamps)",
		-1000, 10000, -1000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 2;

	Param1117=
		0,
		6, "20 65 24 01 30 A8",
		0x04, 0xC3, 2,
		"Process Input Error Low (V)",
		"V",
		"[P1.LE] - Process Input Low Error (volts)",
		-1000, 5000, -1000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 2;

	Param1118=
		0,
		6, "20 65 24 01 30 A9",
		0x04, 0xC3, 2,
		"Process Input Error Low (mV)",
		"mV",
		"[P1.LE] - Process Input Low Error (millivolts)",
		-100, 2500, -100,
		1, 100, 1, 0,
		 ,  ,  ,  , 2;

	Param1119=
		0,
		6, "20 65 24 01 30 AA",
		0x04, 0xC7, 2,
		"Process Input Error High (mA)",
		"mA",
		"[P1.HE] - Process Input High Error (milliamps)",
		10000, 21000, 21000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 2;

	Param1120=
		0,
		6, "20 65 24 01 30 AB",
		0x04, 0xC7, 2,
		"Process Input Error High (V)",
		"V",
		"[P1.HE] - Process Input High Error (volts)",
		5000, 11000, 11000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 2;

	Param1121=
		0,
		6, "20 65 24 01 30 AC",
		0x04, 0xC7, 2,
		"Process Input Error High (mV)",
		"mV",
		"[P1.HE] - Process Input High Error (millivolts)",
		2500, 5100, 5100,
		1, 100, 1, 0,
		 ,  ,  ,  , 2;

	Param1122=
		0,
		6, "20 65 24 01 30 72",
		0x04, 0xC4, 4,
		"Units Scale Low",
		"",
		"[rg.Lo] - Units Scale Low",
		-1999000, 9999000, -1999000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1123=
		0,
		6, "20 65 24 01 30 73",
		0x04, 0xC4, 4,
		"Units Scale High",
		"",
		"[rg.hi] - Units Scale High",
		-1999000, 9999000, 9999000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1124=
		0,
		6, "20 65 24 01 30 74",
		0x04, 0xC4, 4,
		"SP Low Limit (T/C)",
		"°",
		"[SP.Lo] - Set Point Low Limit for Thermocouples",
		-328000, 4200000, -200000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 1;

	Param1125=
		0,
		6, "20 65 24 01 30 75",
		0x04, 0xC4, 4,
		"SP Low Limit (RTD)",
		"°",
		"[SP.Lo] - Set Point Low Limit for RTD",
		-328000, 1472000, -200000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 1;

	Param1126=
		0,
		6, "20 65 24 01 30 76",
		0x04, 0xC4, 4,
		"SP Low Limit (Process)",
		"",
		"[SP.Lo] - Set Point Low Limit for Process",
		-1999000, 9999000, -999000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1127=
		0,
		6, "20 65 24 01 30 77",
		0x04, 0xC4, 4,
		"SP High Limit (T/C)",
		"°",
		"[SP.hi] - Set Point High Limit for Thermocouples",
		-328000, 4200000, 1371111,
		1, 1000, 1, 0,
		 ,  ,  ,  , 1;

	Param1128=
		0,
		6, "20 65 24 01 30 78",
		0x04, 0xC4, 4,
		"SP High Limit (RTD)",
		"°",
		"[SP.hi] - Set Point High Limit for RTD",
		-328000, 1472000, 800000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 1;

	Param1129=
		0,
		6, "20 65 24 01 30 79",
		0x04, 0xC4, 4,
		"SP High Limit (Process)",
		"",
		"[SP.hi] - Set Point High Limit for Process",
		-1999000, 9999000, 999000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1130=
		0,
		6, "20 65 24 01 30 7A",
		0x02, 0xC6, 1,
		"Input Filter",
		"",
		"[Ftr.E] - Input Filter",
		0, 3, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1131=
		0,
		6, "20 65 24 01 30 7B",
		0x04, 0xC8, 4,
		"Filter Value",
		"seconds",
		"[FLtr] - filter Value",
		0, 60000, 0,
		1, 1000, 1, 0,
		 ,  ,  ,  , 1;

	Param1132=
		0,
		6, "20 65 24 01 30 7C",
		0x02, 0xC6, 1,
		"Output 1 Function",
		"",
		"[Ot 1] - Output 1 Function",
		0, 6, 3,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1133=
		0,
		6, "20 65 24 01 30 7D",
		0x02, 0xC1, 1,
		"Output 1 Control Method",
		"",
		"[Ctr1] - Control Method 1",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1134=
		0,
		6, "20 65 24 01 30 7E",
		0x04, 0xC8, 4,
		"Output 1 Fixed Time Base",
		"seconds",
		"[Ftb1] - Fixed Time Base 1",
		100, 60000, 20000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 1;

	Param1135=
		0,
		6, "20 65 24 01 30 7F",
		0x04, 0xC7, 2,
		"Output 1 Power Limit",
		"%",
		"[PL 1] - Power Limit 1",
		0, 10000, 10000,
		1, 100, 1, 0,
		 ,  ,  ,  , 1;

	Param1136=
		0,
		6, "20 65 24 01 30 80",
		0x04, 0xC7, 2,
		"Output 1 Power Scale Low",
		"%",
		"[PSL1] - Output Power Scale Low 1",
		0, 10000, 0,
		1, 100, 1, 0,
		 ,  ,  ,  , 1;

	Param1137=
		0,
		6, "20 65 24 01 30 81",
		0x04, 0xC7, 2,
		"Output 1 Power Scale High",
		"%",
		"[PSH1] - Output Power Scale High 1",
		0, 10000, 10000,
		1, 100, 1, 0,
		 ,  ,  ,  , 1;

	Param1138=
		0,
		6, "20 65 24 01 30 82",
		0x02, 0xC6, 1,
		"Output 1 Non-Linear Function",
		"",
		"[nLF1] - Output Non-Linear Function 1",
		0, 2, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1139=
		0,
		6, "20 65 24 01 30 83",
		0x02, 0xC1, 1,
		"Analog Output 1 Units",
		"",
		"[AO1.U] - Analog Output 1 Units",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1140=
		0,
		6, "20 65 24 01 30 84",
		0x04, 0xC8, 4,
		"Analog Output 1 Scale Low (mA)",
		"mA",
		"[O1.Lo] - Analog Output 1 Scale Low (milliamps)",
		0, 20000, 4000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 2;

	Param1141=
		0,
		6, "20 65 24 01 30 85",
		0x04, 0xC8, 4,
		"Analog Output 1 Scale Low (V)",
		"V",
		"[O1.Lo] - Analog Output 1 Scale Low (volts)",
		0, 10000, 0,
		1, 1000, 1, 0,
		 ,  ,  ,  , 2;

	Param1142=
		0,
		6, "20 65 24 01 30 86",
		0x04, 0xC8, 4,
		"Analog Output 1 Scale High (mA)",
		"mA",
		"[O1.hi] - Analog Output 1 Scale High (milliamps)",
		0, 20000, 20000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 2;

	Param1143=
		0,
		6, "20 65 24 01 30 87",
		0x04, 0xC8, 4,
		"Analog Output 1 Scale High (V)",
		"V",
		"[O1.hi] - Analog Output 1 Scale High (volts)",
		0, 10000, 10000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 2;

	Param1144=
		0,
		6, "20 65 24 01 30 AD",
		0x02, 0xC1, 1,
		"Output 1 Retransmit Source",
		"",
		"[r1.So] - Output 1 Retransmit Source",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1145=
		0,
		6, "20 65 24 01 30 AE",
		0x04, 0xC4, 4,
		"Output 1 Retransmit Scale Low",
		"",
		"[r1.Lo] - Output 1 Retransmit Low Scale",
		-1999000, 9999000, -17777,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1146=
		0,
		6, "20 65 24 01 30 AF",
		0x04, 0xC4, 4,
		"Output 1 Retransmit Scale High",
		"",
		"[r1.hi] - Output 1 Retransmit High Scale",
		-1999000, 9999000, 260000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1147=
		0,
		6, "20 65 24 01 30 B0",
		0x04, 0xC4, 4,
		"Output 1 Retransmit Offset",
		"",
		"[r1.CO] - Output 1 Retransmit Offset",
		-999000, 999000, 0,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1148=
		0,
		6, "20 65 24 01 30 88",
		0x02, 0xC6, 1,
		"Output 2 Function",
		"",
		"[Ot 2] - Output 2 Function",
		0, 4, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1149=
		0,
		6, "20 65 24 01 30 89",
		0x02, 0xC1, 1,
		"Output 2 Control Method",
		"",
		"[Ctr2] - Control Method 2",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1150=
		0,
		6, "20 65 24 01 30 8A",
		0x04, 0xC8, 4,
		"Output 2 Fixed Time Base",
		"seconds",
		"[Ftb2] - Fixed Time Base 2",
		100, 60000, 20000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 1;

	Param1151=
		0,
		6, "20 65 24 01 30 8B",
		0x04, 0xC7, 2,
		"Output 2 Power Limit",
		"%",
		"[PL 2] - Power Limit 2",
		0, 10000, 10000,
		1, 100, 1, 0,
		 ,  ,  ,  , 1;

	Param1152=
		0,
		6, "20 65 24 01 30 8C",
		0x04, 0xC7, 2,
		"Output 2 Power Scale Low",
		"%",
		"[PSL2] - Output Power Scale Low 2",
		0, 10000, 0,
		1, 100, 1, 0,
		 ,  ,  ,  , 1;

	Param1153=
		0,
		6, "20 65 24 01 30 8D",
		0x04, 0xC7, 2,
		"Output 2 Power Scale High",
		"%",
		"[PSH2] - Output Power Scale High 2",
		0, 10000, 10000,
		1, 100, 1, 0,
		 ,  ,  ,  , 1;

	Param1154=
		0,
		6, "20 65 24 01 30 8E",
		0x02, 0xC6, 1,
		"Output 2 Non-Linear Function",
		"",
		"[nLF2] - Output Non-Linear Function 2",
		0, 2, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1155=
		0,
		6, "20 65 24 01 30 8F",
		0x04, 0xC8, 4,
		"Alarm 1 Hysteresis",
		"",
		"[hyS1] - Alarm 1 Hysteresis",
		0, 999000, 555,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1156=
		0,
		6, "20 65 24 01 30 90",
		0x02, 0xC1, 1,
		"Alarm 1 Logic",
		"",
		"[Lgc1] - Alarm 1 Logic",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1157=
		0,
		6, "20 65 24 01 30 91",
		0x02, 0xC1, 1,
		"Alarm 1 Latching",
		"",
		"[LAt1] - Alarm 1 Latching",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1158=
		0,
		6, "20 65 24 01 30 92",
		0x02, 0xC1, 1,
		"Alarm 1 Silencing",
		"",
		"[SiL1] - Alarm 1 Silencing",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1159=
		0,
		6, "20 65 24 01 30 93",
		0x02, 0xC1, 1,
		"Alarm 1 Message",
		"",
		"[dSP1] - Alarm 1 Message",
		0, 1, 1,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1160=
		0,
		6, "20 65 24 01 30 94",
		0x04, 0xC8, 4,
		"Alarm 2 Hysteresis",
		"",
		"[hyS2] - Alarm 2 Hysteresis",
		0, 999000, 555,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1161=
		0,
		6, "20 65 24 01 30 95",
		0x02, 0xC1, 1,
		"Alarm 2 Logic",
		"",
		"[Lgc2] - Alarm 2 Logic",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1162=
		0,
		6, "20 65 24 01 30 96",
		0x02, 0xC1, 1,
		"Alarm 2 Latching",
		"",
		"[LAt2] - Alarm 2 Latching",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1163=
		0,
		6, "20 65 24 01 30 97",
		0x02, 0xC1, 1,
		"Alarm 2 Silencing",
		"",
		"[SiL2] - Alarm 2 Silencing",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1164=
		0,
		6, "20 65 24 01 30 98",
		0x02, 0xC1, 1,
		"Alarm 2 Message",
		"",
		"[dSP2] - Alarm 2 Message",
		0, 1, 1,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1165=
		0,
		6, "20 65 24 01 30 A4",
		0x02, 0xC1, 1,
		"AC Line Frequency",
		"",
		"[ACLF] - AC Line Frequency",
		0, 1, 1,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1166=
		0,
		6, "20 65 24 01 30 99",
		0x02, 0xC1, 1,
		"Units of Measurement",
		"",
		"[Unit] - Units of Measurement",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1167=
		0,
		6, "20 65 24 01 30 9A",
		0x02, 0xC1, 1,
		"Input Error Latching",
		"",
		"[I.Err] - Input Error Latching",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1168=
		0,
		6, "20 65 24 01 30 9B",
		0x02, 0xC6, 1,
		"Input Error Failure Mode",
		"",
		"[FAIL] - Input Error Failure Mode",
		0, 2, 1,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1169=
		0,
		6, "20 65 24 01 30 9C",
		0x04, 0xC3, 2,
		"Input Error Power",
		"%",
		"[MAn] - Input Error Power",
		-10000, 10000, 0,
		1, 100, 1, 0,
		 ,  ,  ,  , 1;

	Param1170=
		0,
		6, "20 65 24 01 30 9D",
		0x02, 0xC6, 1,
		"Active Displays",
		"",
		"[ dSP] - Active Displays",
		0, 2, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1171=
		0,
		6, "20 65 24 01 30 9E",
		0x02, 0xC6, 1,
		"Ramp Mode",
		"",
		"[  rP] - Ramping Mode",
		0, 2, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1172=
		0,
		6, "20 65 24 01 30 9F",
		0x02, 0xC1, 1,
		"Ramp Scale",
		"",
		"[rP.Sc] - Ramp Scale",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1173=
		0,
		6, "20 65 24 01 30 A0",
		0x04, 0xC8, 4,
		"Ramp Rate",
		"",
		"[rP.rt] - Ramp Rate",
		0, 9999000, 55555,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1174=
		0,
		6, "20 65 24 01 30 A1",
		0x02, 0xC6, 1,
		"Lockout",
		"",
		"[ LOC] - Lockout",
		0, 4, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

$ End of Setup page, start of Operations page

	Param1200=
		0,
		6, "20 66 24 01 30 67",
		0x34, 0xC7, 2,
		"Power Heat",
		"%",
		"[Po.ht] - Power Heat",
		0, 10000, 0,
		1, 100, 1, 0,
		 ,  ,  ,  , 1;

	Param1201=
		0,
		6, "20 66 24 01 30 68",
		0x34, 0xC7, 2,
		"Power Cool",
		"%",
		"[Po.CL] - Power Cool",
		0, 10000, 0,
		1, 100, 1, 0,
		 ,  ,  ,  , 1;

	Param1202=
		0,
		6, "20 66 24 01 30 66",
		0x02, 0xC1, 1,
		"Auto-Manual Mode",
		"",
		"[A-M] - Auto-Manual Mode",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1203=
		0,
		6, "20 66 24 01 30 65",
		0x02, 0xC1, 1,
		"Autotune",
		"",
		"[ Aut] - Autotune",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1204=
		0,
		6, "20 66 24 01 30 64",
		0x04, 0xC4, 4,
		"Calibration Offset",
		"",
		"[ CAL] - Calibration Offset",
		-999000, 999000, 0,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1205=
		0,
		6, "20 66 24 01 30 69",
		0x02, 0xC6, 1,
		"Heat Control Method",
		"",
		"[ht.M] - Heat Control Method",
		0, 2, 1,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1206=
		0,
		6, "20 66 24 01 30 6A",
		0x04, 0xC8, 4,
		"Heat PB (Temperature)",
		"°",
		"[Pb.ht] - Proportional Band Heat for Temperature",
		555, 999000, 13888,
		1, 1000, 1, 0,
		 ,  ,  ,  , 1;

	Param1207=
		0,
		6, "20 66 24 01 30 6B",
		0x04, 0xC8, 4,
		"Heat PB (Process)",
		"",
		"Proportional Band Heat for Process",
		1, 999000, 25000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1208=
		0,
		6, "20 66 24 01 30 6C",
		0x04, 0xC8, 4,
		"Heat Reset / Integral",
		"",
		"[rE.ht] / [It.ht] - Reset / Integral Heat",
		0, 99990, 0,
		1, 1000, 1, 0,
		 ,  ,  ,  , 2;

	Param1209=
		0,
		6, "20 66 24 01 30 6D",
		0x04, 0xC8, 4,
		"Heat Rate / Derivative",
		"minutes",
		"[rA.ht] / [dE.ht] - Rate / Derivative Heat",
		0, 9990, 0,
		1, 1000, 1, 0,
		 ,  ,  ,  , 2;

	Param1210=
		0,
		6, "20 66 24 01 30 6E",
		0x04, 0xC8, 4,
		"Heat Dead Band",
		"",
		"[db.ht] - Dead Band Heat",
		0, 999000, 0,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1211=
		0,
		6, "20 66 24 01 30 6F",
		0x04, 0xC8, 4,
		"Heat Hysteresis (Temperature)",
		"°",
		"[h.hyS] - Heat Hysteresis for Temperature",
		555, 999000, 600,
		1, 1000, 1, 0,
		 ,  ,  ,  , 1;

	Param1212=
		0,
		6, "20 66 24 01 30 70",
		0x04, 0xC8, 4,
		"Heat Hysteresis (Process)",
		"",
		"[h.hyS] - Heat Hysteresis for Process",
		0, 999000, 1000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1213=
		0,
		6, "20 66 24 01 30 71",
		0x02, 0xC6, 1,
		"Cool Control Method",
		"",
		"[CL.M] - Cool Control Method",
		0, 2, 1,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1214=
		0,
		6, "20 66 24 01 30 72",
		0x04, 0xC8, 4,
		"Cool PB (Temperature)",
		"°",
		"[Pb.CL] - Proportional Band Cool for Temperature",
		555, 999000, 13888,
		1, 1000, 1, 0,
		 ,  ,  ,  , 1;

	Param1215=
		0,
		6, "20 66 24 01 30 73",
		0x04, 0xC8, 4,
		"Cool PB (Process)",
		"",
		"[Pb.CL] - Proportional Band Cool for Process",
		1, 999000, 25000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1216=
		0,
		6, "20 66 24 01 30 74",
		0x04, 0xC8, 4,
		"Cool Reset / Integral",
		"",
		"[rE.CL] / [It.CL] - Reset / Integral Cool",
		0, 99990, 0,
		1, 1000, 1, 0,
		 ,  ,  ,  , 2;

	Param1217=
		0,
		6, "20 66 24 01 30 75",
		0x04, 0xC8, 4,
		"Cool Rate / Derivative",
		"minutes",
		"[rA.CL] / [dE.CL] - Rate / Derivative Cool",
		0, 9990, 0,
		1, 1000, 1, 0,
		 ,  ,  ,  , 2;

	Param1218=
		0,
		6, "20 66 24 01 30 76",
		0x04, 0xC8, 4,
		"Cool Dead Band",
		"",
		"[db.CL] - Dead Band Cool",
		0, 999000, 0,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1219=
		0,
		6, "20 66 24 01 30 77",
		0x04, 0xC8, 4,
		"Cool Hysteresis (Temperature)",
		"°",
		"[C.hyS] - Cool Hysteresis for Temperature",
		555, 999000, 600,
		1, 1000, 1, 0,
		 ,  ,  ,  , 1;

	Param1220=
		0,
		6, "20 66 24 01 30 78",
		0x04, 0xC8, 4,
		"Cool Hysteresis (Process)",
		"",
		"[C.hyS] - Cool Hysteresis for Process",
		0, 999000, 1000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1221=
		0,
		6, "20 66 24 01 30 79",
		0x34, 0xC7, 2,
		"P Term",
		"%",
		"[ProP] - Proportional Term",
		0, 1000, 0,
		1, 10, 1, 0,
		 ,  ,  ,  , 1;

	Param1222=
		0,
		6, "20 66 24 01 30 7A",
		0x34, 0xC7, 2,
		"I Term",
		"%",
		"[  it] - Integral Term",
		0, 1000, 0,
		1, 10, 1, 0,
		 ,  ,  ,  , 1;

	Param1223=
		0,
		6, "20 66 24 01 30 7B",
		0x34, 0xC7, 2,
		"D Term",
		"%",
		"[  dE] - Derivative Term",
		0, 1000, 0,
		1, 10, 1, 0,
		 ,  ,  ,  , 1;

	Param1224=
		0,
		6, "20 66 24 01 30 7C",
		0x04, 0xC4, 4,
		"Alarm 1 High (Deviation)",
		"",
		"[A1.hi] - Alarm 1 High for Deviation Alarms",
		0, 9999000, 555000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1225=
		0,
		6, "20 66 24 01 30 7D",
		0x04, 0xC4, 4,
		"Alarm 1 High (Process)",
		"",
		"[A1.hi] - Alarm 1 High for Process Alarms",
		-1999000, 9999000, 1371111,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1226=
		0,
		6, "20 66 24 01 30 7E",
		0x04, 0xC4, 4,
		"Alarm 1 Low (Deviation)",
		"",
		"[A1.Lo] - Alarm 1 Low for Deviation Alarms",
		-1999000, 0, -555000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1227=
		0,
		6, "20 66 24 01 30 7F",
		0x04, 0xC4, 4,
		"Alarm 1 Low (Process)",
		"",
		"[A1.Lo] - Alarm 1 Low for Process Alarms",
		-1999000, 9999000, -200000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1228=
		0,
		6, "20 66 24 01 30 80",
		0x04, 0xC4, 4,
		"Alarm 2 High (Deviation)",
		"",
		"[A2.hi] - Alarm 2 High for Deviation Alarms",
		0, 9999000, 555000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1229=
		0,
		6, "20 66 24 01 30 81",
		0x04, 0xC4, 4,
		"Alarm 2 High (Process)",
		"",
		"[A2.hi] - Alarm 2 High for Process Alarms",
		-1999000, 9999000, 1371111,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1230=
		0,
		6, "20 66 24 01 30 82",
		0x04, 0xC4, 4,
		"Alarm 2 Low (Deviation)",
		"",
		"[A2.Lo] - Alarm 2 Low for Deviation Alarms",
		-1999000, 0, -555000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1231=
		0,
		6, "20 66 24 01 30 83",
		0x04, 0xC4, 4,
		"Alarm 2 Low (Process)",
		"",
		"[A2.Lo] - Alarm 2 Low for Process Alarms",
		-1999000, 9999000, -200000,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

$ End of Operations page, start of Programming page

	Param1300=
		0,
		6, "20 68 24 01 30 64",
		0x02, 0xC6, 1,
		"P1",
		"",
		"[  P1] - Programmable Page 1",
		0, 30, 13,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1301=
		0,
		6, "20 68 24 01 30 65",
		0x02, 0xC6, 1,
		"P2",
		"",
		"[  P2] - Programmable Page 2",
		0, 30, 12,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1302=
		0,
		6, "20 68 24 01 30 66",
		0x02, 0xC6, 1,
		"P3",
		"",
		"[  P3] - Programmable Page 3",
		0, 30, 11,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1303=
		0,
		6, "20 68 24 01 30 67",
		0x02, 0xC6, 1,
		"P4",
		"",
		"[  P4] - Programmable Page 4",
		0, 30, 1,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1304=
		0,
		6, "20 68 24 01 30 68",
		0x02, 0xC6, 1,
		"P5",
		"",
		"[  P5] - Programmable Page 5",
		0, 30, 15,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1305=
		0,
		6, "20 68 24 01 30 69",
		0x02, 0xC6, 1,
		"P6",
		"",
		"[  P6] - Programmable Page 6",
		0, 30, 16,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1306=
		0,
		6, "20 68 24 01 30 6A",
		0x02, 0xC6, 1,
		"P7",
		"",
		"[  P7] - Programmable Page 7",
		0, 30, 17,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1307=
		0,
		6, "20 68 24 01 30 6B",
		0x02, 0xC6, 1,
		"P8",
		"",
		"[  P8] - Programmable Page 8",
		0, 30, 18,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1308=
		0,
		6, "20 68 24 01 30 6C",
		0x02, 0xC6, 1,
		"P9",
		"",
		"[  P9] - Programmable Page 9",
		0, 30, 20,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1309=
		0,
		6, "20 68 24 01 30 6D",
		0x02, 0xC6, 1,
		"P10",
		"",
		"[ P10] - Programmable Page 10",
		0, 30, 21,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1310=
		0,
		6, "20 68 24 01 30 6E",
		0x02, 0xC6, 1,
		"P11",
		"",
		"[ P11] - Programmable Page 11",
		0, 30, 22,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1311=
		0,
		6, "20 68 24 01 30 6F",
		0x02, 0xC6, 1,
		"P12",
		"",
		"[ P12] - Programmable Page 12",
		0, 30, 23,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1312=
		0,
		6, "20 68 24 01 30 70",
		0x02, 0xC6, 1,
		"P13",
		"",
		"[ P13] - Programmable Page 13",
		0, 30, 24,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1313=
		0,
		6, "20 68 24 01 30 71",
		0x02, 0xC6, 1,
		"P14",
		"",
		"[ P14] - Programmable Page 14",
		0, 30, 26,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1314=
		0,
		6, "20 68 24 01 30 72",
		0x02, 0xC6, 1,
		"P15",
		"",
		"[ P15] - Programmable Page 15",
		0, 30, 4,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1315=
		0,
		6, "20 68 24 01 30 73",
		0x02, 0xC6, 1,
		"P16",
		"",
		"[ P16] - Programmable Page 16",
		0, 30, 3,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1316=
		0,
		6, "20 68 24 01 30 74",
		0x02, 0xC6, 1,
		"P17",
		"",
		"[ P17] - Programmable Page 17",
		0, 30, 6,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1317=
		0,
		6, "20 68 24 01 30 75",
		0x02, 0xC6, 1,
		"P18",
		"",
		"[ P18] - Programmable Page 18",
		0, 30, 5,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1318=
		0,
		6, "20 68 24 01 30 76",
		0x02, 0xC6, 1,
		"P19",
		"",
		"[ P19] - Programmable Page 19",
		0, 30, 9,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1319=
		0,
		6, "20 68 24 01 30 77",
		0x02, 0xC6, 1,
		"P20",
		"",
		"[ P20] - Programmable Page 20",
		0, 30, 10,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

$ End of Programming page, start of Factory page

	Param1400=
		0,
		6, "20 67 24 01 30 64",
		0x34, 0xC4, 4,
		"Ambient Temperature",
		"°F",
		"[AMb] - Ambient Temperature",
		-50000, 300000, 0,
		1, 1000, 1, 0,
		 ,  ,  ,  , 1;

	Param1401=
		0,
		6, "20 67 24 01 30 65",
		0x34, 0xC7, 2,
		"Output 1 Process Value",
		"",
		"[A.Ot1] - Output 1 Process Value",
		0, 22000, 0,
		1, 1000, 1, 0,
		 ,  ,  ,  , 2;

	Param1402=
		0,
		6, "20 67 24 01 30 66",
		0x02, 0xC1, 1,
		"Restore Calibration",
		"",
		"[rESt] - Restore Factory Calibration",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1403=
		0,
		6, "20 67 24 01 30 67",
		0x02, 0xC6, 1,
		"Restore User Settings",
		"",
		"[Usr.r] - Restore User Settings",
		0, 2, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1404=
		0,
		6, "20 67 24 01 30 68",
		0x02, 0xC6, 1,
		"Save User Settings",
		"",
		"[Usr.s] - Save User Settings",
		0, 2, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1405=
		0,
		6, "20 67 24 01 30 69",
		0x02, 0xC1, 1,
		"Default Parameters",
		"",
		"[dFLt] - Default Parameters",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1406=
		0,
		6, "20 67 24 01 30 6A",
		0x12, 0xC6, 1,
		"Output 1 Type",
		"",
		"[O.ty1] - Output 1 Type",
		0, 5, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1407=
		0,
		6, "20 67 24 01 30 6B",
		0x12, 0xC6, 1,
		"Output 2 Type",
		"",
		"[O.ty2] - Output 2 Type",
		0, 5, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1408=
		0,
		6, "20 67 24 01 30 6C",
		0x10, 0xC7, 2,
		"Software ID",
		"",
		"[ S.id] - Software ID",
		0, 9999, 16,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1409=
		0,
		6, "20 67 24 01 30 6F",
		0x10, 0xC7, 2,
		"Software Release Version",
		"",
		"[S.VEr] - Software Release Version",
		0, 9999, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1410=
		0,
		6, "20 67 24 01 30 70",
		0x10, 0xC7, 2,
		"Software Prototype Version",
		"",
		"[S.VEr] - Software Prototype Version",
		0, 9999, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1411=
		0,
		6, "20 67 24 01 30 6D",
		0x10, 0xC7, 2,
		"Software Build Number",
		"",
		"[S.bLd] - Software Build Number",
		0, 9999, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

$ Removed:  Unused parameter.
$	Param1412=
$		0,
$		6, "20 67 24 01 30 71",
$		0x10, 0xC7, 2,
$		"Software Branch Number",
$		"",
$		"Software Branch Number",
$		0, 9999, 0,
$		 ,  ,  ,  ,
$		 ,  ,  ,  ,  ;

	Param1413=
		0,
		6, "20 67 24 01 30 6E",
		0x10, 0xC8, 4,
		"Serial Number",
		"",
		"[ Sn-], [ Sn_] - Serial Number",
		0, 99999999, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

$ Removed:  Unused parameter.
$	Param1414=
$		0,
$		6, "20 67 24 01 30 87",
$		0x10, 0xC7, 2,
$		"Date Code",
$		"",
$		"Date Code (yy/ww)",
$		0, 9999, 0,
$		 ,  ,  ,  ,
$		 ,  ,  ,  ,  ;

$ End of Factory page, start of Home page

	Param1500=
		0,
		6, "20 64 24 01 30 64",
		0x34, 0xC4, 4,
		"PV",
		"",
		"Process Value",
		-1999000, 9999999, 0,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1501=
		0,
		6, "20 64 24 01 30 65",
		0x04, 0xC4, 4,
		"Closed Loop SP",
		"",
		"Closed Loop Set Point",
		-2000000001, 9999000, 23888,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1502=
		0,
		6, "20 64 24 01 30 66",
		0x34, 0xC4, 4,
		"Filtered PV",
		"",
		"Filtered Process Value",
		-1999000, 9999999, 0,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

	Param1503=
		0,
		6, "20 64 24 01 30 67",
		0x04, 0xC3, 2,
		"Open Loop Output Power",
		"%",
		"Open Loop Output Power",
		-10000, 10000, 0,
		1, 100, 1, 0,
		 ,  ,  ,  , 1;

	Param1504=
		0,
		6, "20 64 24 01 30 68",
		0x34, 0xC4, 4,
		"Current Ramp SP",
		"",
		"[  rP] - Current Ramp (Working) Set Point",
		-2000000001, 9999000, 0,
		1, 1000, 1, 0,
		 ,  ,  ,  , 3;

$ Removed:  Same as Param1501.
$	Param1505=
$		0,
$		6, "20 64 24 01 30 69",
$		0x04, 0xC4, 4,
$		"Ramp Target SP",
$		"",
$		"Ramp Target Set Point",
$		-2000000001, 9999000, 75000,
$		1, 1000, 1, 0,
$		 ,  ,  ,  , 3;

	Param1506=
		0,
		6, "20 64 24 01 30 6A",
		0x30, 0xC7, 2,
		"Input Error",
		"",
		"[Er.In] - Input Error",
		0, 19999, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1507=
		0,
		6, "20 64 24 01 30 6B",
		0x32, 0xC1, 1,
		"Alarm 1 Low Status",
		"",
		"[A1.Lo] - Alarm Low 1 Status",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1508=
		0,
		6, "20 64 24 01 30 6C",
		0x32, 0xC1, 1,
		"Alarm 1 High Status",
		"",
		"[A1.hi] - Alarm High 1 Status",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1509=
		0,
		6, "20 64 24 01 30 6D",
		0x32, 0xC1, 1,
		"Alarm 2 Low Status",
		"",
		"[A2.Lo] - Alarm Low 2 Status",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1510=
		0,
		6, "20 64 24 01 30 6E",
		0x32, 0xC1, 1,
		"Alarm 2 High Status",
		"",
		"[A2.hi] - Alarm High 2 Status",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1511=
		0,
		6, "20 65 24 01 30 A2",
		0x02, 0xC1, 1,
		"Alarm 1 ACK",
		"",
		"Alarm 1 Acknowledge",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

	Param1512=
		0,
		6, "20 65 24 01 30 A3",
		0x02, 0xC1, 1,
		"Alarm 2 ACK",
		"",
		"Alarm 2 Acknowledge",
		0, 1, 0,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

$ End of Home page

$ NOTE:  The following parameters MUST remain last in order for ADR to work properly!
	Param1999=
		0,
		6, "20 67 24 01 30 85",
		0x02, 0xC1, 1,
		"Non-Volatile Writes",
		"",
		"Non-Volatile Writes",
		0, 1, 1,
		 ,  ,  ,  ,
		 ,  ,  ,  ,  ;

[EnumPar]

$ NOTE:  The following parameters MUST remain first in order for ADR to work properly!
	Param1001=
		"°F",
		"°C";

$ Start of Setup page

	Param1100=
		"T/C",
		"RTD",
		"mA",
		"volts",
		"Reserved",
		"mV";

	Param1101=
		"J",
		"K",
		"T",
		"E",
		"N",
		"C",
		"D",
		"PTII",
		"R",
		"S",
		"B";

	Param1102=
		"°F",
		"°C";

	Param1103=
		"0",
		"0.0";

	Param1104=
		"0",
		"0.0",
		"0.00",
		"0.000";

	Param1105=
		"No",
		"Yes";

	Param1130=
		"Off",
		"Filter Display",
		"Filter Input",
		"Filter Both";

	Param1132=
		"Off",
		"Process Alarm",
		"Deviation Alarm",
		"Heat Control",
		"Cool Control",
		"Reserved",
		"Retransmit";

	Param1133=
		"Fixed Time Base",
		"Variable Time Base";

	Param1138=
		"Off",
		"Curve 1",
		"Curve 2";


	Param1139=
		"mA",
		"volts";

	Param1144=
		"Process Value",
		"Set Point";

	Param1148=
		"Off",
		"Process Alarm",
		"Deviation Alarm",
		"Heat Control",
		"Cool Control";

	Param1149=
		"Fixed Time Base",
		"Variable Time Base";

	Param1154=
		"Off",
		"Curve 1",
		"Curve 2";

	Param1156=
		"Closed",
		"Open";

	Param1157=
		"Off",
		"On";

	Param1158=
		"No Silencing",
		"Silencing";

	Param1159=
		"No Message",
		"Message";

	Param1161=
		"Closed",
		"Open";

	Param1162=
		"Off",
		"On";

	Param1163=
		"No Silencing",
		"Silencing";

	Param1164=
		"No Message",
		"Message";

	Param1165=
		"50 Hz",
		"60 Hz";

	Param1166=
		"US",
		"SI";

	Param1167=
		"Off",
		"On";

	Param1168=
		"Off",
		"Bumpless",
		"Manual";

	Param1170=
		"Both Displays On",
		"Lower Display Only",
		"Upper Display Only";

	Param1171=
		"Off",
		"Start-up",
		"Start-up, SP Change";

	Param1172=
		"Hours",
		"Minutes";

	Param1174=
		"0 - No Lockout",
		"1 - Set Point, Auto-Manual, Alarms Only",
		"2 - Set Point, Auto-Manual Only",
		"3 - Set Point Only",
		"4 - Full Lockout";

$ End of Setup page, start of Operations page

	Param1202=
		"Auto",
		"Manual";

	Param1203=
		"Off",
		"On";

	Param1205=
		"Off",
		"PID",
		"On-Off";

	Param1213=
		"Off",
		"PID",
		"On-Off";

$ End of Operations page, start of Programming page

	Param1300=
		"None",
		"Calibration Offset",
		"Temperature Units",
		"Alarm 1 Low",
		"Alarm 1 High",
		"Alarm 2 Low",
		"Alarm 2 High",
		"Alarm Hysteresis 1",
		"Alarm Hysteresis 2",
		"MAC ID",
		"Baud Rate",
		"Autotune",
		"Auto-Manual",
		"Power Heat",
		"Power Cool",
		"Heat Control Method",
		"Heat PB",
		"Heat Reset / Integral",
		"Heat Rate / Derivative",
		"Heat Dead Band",
		"Heat Hysteresis",
		"Cool Control Method",
		"Cool PB",
		"Cool Reset / Integral",
		"Cool Rate / Derivative",
		"Cool Dead Band",
		"Cool Hysteresis",
		"Proportional Term",
		"Integral Term",
		"Derivative Term",
		"Ramp Rate";

	Param1301=
		"None",
		"Calibration Offset",
		"Temperature Units",
		"Alarm 1 Low",
		"Alarm 1 High",
		"Alarm 2 Low",
		"Alarm 2 High",
		"Alarm Hysteresis 1",
		"Alarm Hysteresis 2",
		"MAC ID",
		"Baud Rate",
		"Autotune",
		"Auto-Manual",
		"Power Heat",
		"Power Cool",
		"Heat Control Method",
		"Heat PB",
		"Heat Reset / Integral",
		"Heat Rate / Derivative",
		"Heat Dead Band",
		"Heat Hysteresis",
		"Cool Control Method",
		"Cool PB",
		"Cool Reset / Integral",
		"Cool Rate / Derivative",
		"Cool Dead Band",
		"Cool Hysteresis",
		"Proportional Term",
		"Integral Term",
		"Derivative Term",
		"Ramp Rate";

	Param1302=
		"None",
		"Calibration Offset",
		"Temperature Units",
		"Alarm 1 Low",
		"Alarm 1 High",
		"Alarm 2 Low",
		"Alarm 2 High",
		"Alarm Hysteresis 1",
		"Alarm Hysteresis 2",
		"MAC ID",
		"Baud Rate",
		"Autotune",
		"Auto-Manual",
		"Power Heat",
		"Power Cool",
		"Heat Control Method",
		"Heat PB",
		"Heat Reset / Integral",
		"Heat Rate / Derivative",
		"Heat Dead Band",
		"Heat Hysteresis",
		"Cool Control Method",
		"Cool PB",
		"Cool Reset / Integral",
		"Cool Rate / Derivative",
		"Cool Dead Band",
		"Cool Hysteresis",
		"Proportional Term",
		"Integral Term",
		"Derivative Term",
		"Ramp Rate";

	Param1303=
		"None",
		"Calibration Offset",
		"Temperature Units",
		"Alarm 1 Low",
		"Alarm 1 High",
		"Alarm 2 Low",
		"Alarm 2 High",
		"Alarm Hysteresis 1",
		"Alarm Hysteresis 2",
		"MAC ID",
		"Baud Rate",
		"Autotune",
		"Auto-Manual",
		"Power Heat",
		"Power Cool",
		"Heat Control Method",
		"Heat PB",
		"Heat Reset / Integral",
		"Heat Rate / Derivative",
		"Heat Dead Band",
		"Heat Hysteresis",
		"Cool Control Method",
		"Cool PB",
		"Cool Reset / Integral",
		"Cool Rate / Derivative",
		"Cool Dead Band",
		"Cool Hysteresis",
		"Proportional Term",
		"Integral Term",
		"Derivative Term",
		"Ramp Rate";

	Param1304=
		"None",
		"Calibration Offset",
		"Temperature Units",
		"Alarm 1 Low",
		"Alarm 1 High",
		"Alarm 2 Low",
		"Alarm 2 High",
		"Alarm Hysteresis 1",
		"Alarm Hysteresis 2",
		"MAC ID",
		"Baud Rate",
		"Autotune",
		"Auto-Manual",
		"Power Heat",
		"Power Cool",
		"Heat Control Method",
		"Heat PB",
		"Heat Reset / Integral",
		"Heat Rate / Derivative",
		"Heat Dead Band",
		"Heat Hysteresis",
		"Cool Control Method",
		"Cool PB",
		"Cool Reset / Integral",
		"Cool Rate / Derivative",
		"Cool Dead Band",
		"Cool Hysteresis",
		"Proportional Term",
		"Integral Term",
		"Derivative Term",
		"Ramp Rate";

	Param1305=
		"None",
		"Calibration Offset",
		"Temperature Units",
		"Alarm 1 Low",
		"Alarm 1 High",
		"Alarm 2 Low",
		"Alarm 2 High",
		"Alarm Hysteresis 1",
		"Alarm Hysteresis 2",
		"MAC ID",
		"Baud Rate",
		"Autotune",
		"Auto-Manual",
		"Power Heat",
		"Power Cool",
		"Heat Control Method",
		"Heat PB",
		"Heat Reset / Integral",
		"Heat Rate / Derivative",
		"Heat Dead Band",
		"Heat Hysteresis",
		"Cool Control Method",
		"Cool PB",
		"Cool Reset / Integral",
		"Cool Rate / Derivative",
		"Cool Dead Band",
		"Cool Hysteresis",
		"Proportional Term",
		"Integral Term",
		"Derivative Term",
		"Ramp Rate";

	Param1306=
		"None",
		"Calibration Offset",
		"Temperature Units",
		"Alarm 1 Low",
		"Alarm 1 High",
		"Alarm 2 Low",
		"Alarm 2 High",
		"Alarm Hysteresis 1",
		"Alarm Hysteresis 2",
		"MAC ID",
		"Baud Rate",
		"Autotune",
		"Auto-Manual",
		"Power Heat",
		"Power Cool",
		"Heat Control Method",
		"Heat PB",
		"Heat Reset / Integral",
		"Heat Rate / Derivative",
		"Heat Dead Band",
		"Heat Hysteresis",
		"Cool Control Method",
		"Cool PB",
		"Cool Reset / Integral",
		"Cool Rate / Derivative",
		"Cool Dead Band",
		"Cool Hysteresis",
		"Proportional Term",
		"Integral Term",
		"Derivative Term",
		"Ramp Rate";

	Param1307=
		"None",
		"Calibration Offset",
		"Temperature Units",
		"Alarm 1 Low",
		"Alarm 1 High",
		"Alarm 2 Low",
		"Alarm 2 High",
		"Alarm Hysteresis 1",
		"Alarm Hysteresis 2",
		"MAC ID",
		"Baud Rate",
		"Autotune",
		"Auto-Manual",
		"Power Heat",
		"Power Cool",
		"Heat Control Method",
		"Heat PB",
		"Heat Reset / Integral",
		"Heat Rate / Derivative",
		"Heat Dead Band",
		"Heat Hysteresis",
		"Cool Control Method",
		"Cool PB",
		"Cool Reset / Integral",
		"Cool Rate / Derivative",
		"Cool Dead Band",
		"Cool Hysteresis",
		"Proportional Term",
		"Integral Term",
		"Derivative Term",
		"Ramp Rate";

	Param1308=
		"None",
		"Calibration Offset",
		"Temperature Units",
		"Alarm 1 Low",
		"Alarm 1 High",
		"Alarm 2 Low",
		"Alarm 2 High",
		"Alarm Hysteresis 1",
		"Alarm Hysteresis 2",
		"MAC ID",
		"Baud Rate",
		"Autotune",
		"Auto-Manual",
		"Power Heat",
		"Power Cool",
		"Heat Control Method",
		"Heat PB",
		"Heat Reset / Integral",
		"Heat Rate / Derivative",
		"Heat Dead Band",
		"Heat Hysteresis",
		"Cool Control Method",
		"Cool PB",
		"Cool Reset / Integral",
		"Cool Rate / Derivative",
		"Cool Dead Band",
		"Cool Hysteresis",
		"Proportional Term",
		"Integral Term",
		"Derivative Term",
		"Ramp Rate";

	Param1309=
		"None",
		"Calibration Offset",
		"Temperature Units",
		"Alarm 1 Low",
		"Alarm 1 High",
		"Alarm 2 Low",
		"Alarm 2 High",
		"Alarm Hysteresis 1",
		"Alarm Hysteresis 2",
		"MAC ID",
		"Baud Rate",
		"Autotune",
		"Auto-Manual",
		"Power Heat",
		"Power Cool",
		"Heat Control Method",
		"Heat PB",
		"Heat Reset / Integral",
		"Heat Rate / Derivative",
		"Heat Dead Band",
		"Heat Hysteresis",
		"Cool Control Method",
		"Cool PB",
		"Cool Reset / Integral",
		"Cool Rate / Derivative",
		"Cool Dead Band",
		"Cool Hysteresis",
		"Proportional Term",
		"Integral Term",
		"Derivative Term",
		"Ramp Rate";

	Param1310=
		"None",
		"Calibration Offset",
		"Temperature Units",
		"Alarm 1 Low",
		"Alarm 1 High",
		"Alarm 2 Low",
		"Alarm 2 High",
		"Alarm Hysteresis 1",
		"Alarm Hysteresis 2",
		"MAC ID",
		"Baud Rate",
		"Autotune",
		"Auto-Manual",
		"Power Heat",
		"Power Cool",
		"Heat Control Method",
		"Heat PB",
		"Heat Reset / Integral",
		"Heat Rate / Derivative",
		"Heat Dead Band",
		"Heat Hysteresis",
		"Cool Control Method",
		"Cool PB",
		"Cool Reset / Integral",
		"Cool Rate / Derivative",
		"Cool Dead Band",
		"Cool Hysteresis",
		"Proportional Term",
		"Integral Term",
		"Derivative Term",
		"Ramp Rate";

	Param1311=
		"None",
		"Calibration Offset",
		"Temperature Units",
		"Alarm 1 Low",
		"Alarm 1 High",
		"Alarm 2 Low",
		"Alarm 2 High",
		"Alarm Hysteresis 1",
		"Alarm Hysteresis 2",
		"MAC ID",
		"Baud Rate",
		"Autotune",
		"Auto-Manual",
		"Power Heat",
		"Power Cool",
		"Heat Control Method",
		"Heat PB",
		"Heat Reset / Integral",
		"Heat Rate / Derivative",
		"Heat Dead Band",
		"Heat Hysteresis",
		"Cool Control Method",
		"Cool PB",
		"Cool Reset / Integral",
		"Cool Rate / Derivative",
		"Cool Dead Band",
		"Cool Hysteresis",
		"Proportional Term",
		"Integral Term",
		"Derivative Term",
		"Ramp Rate";

	Param1312=
		"None",
		"Calibration Offset",
		"Temperature Units",
		"Alarm 1 Low",
		"Alarm 1 High",
		"Alarm 2 Low",
		"Alarm 2 High",
		"Alarm Hysteresis 1",
		"Alarm Hysteresis 2",
		"MAC ID",
		"Baud Rate",
		"Autotune",
		"Auto-Manual",
		"Power Heat",
		"Power Cool",
		"Heat Control Method",
		"Heat PB",
		"Heat Reset / Integral",
		"Heat Rate / Derivative",
		"Heat Dead Band",
		"Heat Hysteresis",
		"Cool Control Method",
		"Cool PB",
		"Cool Reset / Integral",
		"Cool Rate / Derivative",
		"Cool Dead Band",
		"Cool Hysteresis",
		"Proportional Term",
		"Integral Term",
		"Derivative Term",
		"Ramp Rate";

	Param1313=
		"None",
		"Calibration Offset",
		"Temperature Units",
		"Alarm 1 Low",
		"Alarm 1 High",
		"Alarm 2 Low",
		"Alarm 2 High",
		"Alarm Hysteresis 1",
		"Alarm Hysteresis 2",
		"MAC ID",
		"Baud Rate",
		"Autotune",
		"Auto-Manual",
		"Power Heat",
		"Power Cool",
		"Heat Control Method",
		"Heat PB",
		"Heat Reset / Integral",
		"Heat Rate / Derivative",
		"Heat Dead Band",
		"Heat Hysteresis",
		"Cool Control Method",
		"Cool PB",
		"Cool Reset / Integral",
		"Cool Rate / Derivative",
		"Cool Dead Band",
		"Cool Hysteresis",
		"Proportional Term",
		"Integral Term",
		"Derivative Term",
		"Ramp Rate";

	Param1314=
		"None",
		"Calibration Offset",
		"Temperature Units",
		"Alarm 1 Low",
		"Alarm 1 High",
		"Alarm 2 Low",
		"Alarm 2 High",
		"Alarm Hysteresis 1",
		"Alarm Hysteresis 2",
		"MAC ID",
		"Baud Rate",
		"Autotune",
		"Auto-Manual",
		"Power Heat",
		"Power Cool",
		"Heat Control Method",
		"Heat PB",
		"Heat Reset / Integral",
		"Heat Rate / Derivative",
		"Heat Dead Band",
		"Heat Hysteresis",
		"Cool Control Method",
		"Cool PB",
		"Cool Reset / Integral",
		"Cool Rate / Derivative",
		"Cool Dead Band",
		"Cool Hysteresis",
		"Proportional Term",
		"Integral Term",
		"Derivative Term",
		"Ramp Rate";

	Param1315=
		"None",
		"Calibration Offset",
		"Temperature Units",
		"Alarm 1 Low",
		"Alarm 1 High",
		"Alarm 2 Low",
		"Alarm 2 High",
		"Alarm Hysteresis 1",
		"Alarm Hysteresis 2",
		"MAC ID",
		"Baud Rate",
		"Autotune",
		"Auto-Manual",
		"Power Heat",
		"Power Cool",
		"Heat Control Method",
		"Heat PB",
		"Heat Reset / Integral",
		"Heat Rate / Derivative",
		"Heat Dead Band",
		"Heat Hysteresis",
		"Cool Control Method",
		"Cool PB",
		"Cool Reset / Integral",
		"Cool Rate / Derivative",
		"Cool Dead Band",
		"Cool Hysteresis",
		"Proportional Term",
		"Integral Term",
		"Derivative Term",
		"Ramp Rate";

	Param1316=
		"None",
		"Calibration Offset",
		"Temperature Units",
		"Alarm 1 Low",
		"Alarm 1 High",
		"Alarm 2 Low",
		"Alarm 2 High",
		"Alarm Hysteresis 1",
		"Alarm Hysteresis 2",
		"MAC ID",
		"Baud Rate",
		"Autotune",
		"Auto-Manual",
		"Power Heat",
		"Power Cool",
		"Heat Control Method",
		"Heat PB",
		"Heat Reset / Integral",
		"Heat Rate / Derivative",
		"Heat Dead Band",
		"Heat Hysteresis",
		"Cool Control Method",
		"Cool PB",
		"Cool Reset / Integral",
		"Cool Rate / Derivative",
		"Cool Dead Band",
		"Cool Hysteresis",
		"Proportional Term",
		"Integral Term",
		"Derivative Term",
		"Ramp Rate";

	Param1317=
		"None",
		"Calibration Offset",
		"Temperature Units",
		"Alarm 1 Low",
		"Alarm 1 High",
		"Alarm 2 Low",
		"Alarm 2 High",
		"Alarm Hysteresis 1",
		"Alarm Hysteresis 2",
		"MAC ID",
		"Baud Rate",
		"Autotune",
		"Auto-Manual",
		"Power Heat",
		"Power Cool",
		"Heat Control Method",
		"Heat PB",
		"Heat Reset / Integral",
		"Heat Rate / Derivative",
		"Heat Dead Band",
		"Heat Hysteresis",
		"Cool Control Method",
		"Cool PB",
		"Cool Reset / Integral",
		"Cool Rate / Derivative",
		"Cool Dead Band",
		"Cool Hysteresis",
		"Proportional Term",
		"Integral Term",
		"Derivative Term",
		"Ramp Rate";

	Param1318=
		"None",
		"Calibration Offset",
		"Temperature Units",
		"Alarm 1 Low",
		"Alarm 1 High",
		"Alarm 2 Low",
		"Alarm 2 High",
		"Alarm Hysteresis 1",
		"Alarm Hysteresis 2",
		"MAC ID",
		"Baud Rate",
		"Autotune",
		"Auto-Manual",
		"Power Heat",
		"Power Cool",
		"Heat Control Method",
		"Heat PB",
		"Heat Reset / Integral",
		"Heat Rate / Derivative",
		"Heat Dead Band",
		"Heat Hysteresis",
		"Cool Control Method",
		"Cool PB",
		"Cool Reset / Integral",
		"Cool Rate / Derivative",
		"Cool Dead Band",
		"Cool Hysteresis",
		"Proportional Term",
		"Integral Term",
		"Derivative Term",
		"Ramp Rate";

	Param1319=
		"None",
		"Calibration Offset",
		"Temperature Units",
		"Alarm 1 Low",
		"Alarm 1 High",
		"Alarm 2 Low",
		"Alarm 2 High",
		"Alarm Hysteresis 1",
		"Alarm Hysteresis 2",
		"MAC ID",
		"Baud Rate",
		"Autotune",
		"Auto-Manual",
		"Power Heat",
		"Power Cool",
		"Heat Control Method",
		"Heat PB",
		"Heat Reset / Integral",
		"Heat Rate / Derivative",
		"Heat Dead Band",
		"Heat Hysteresis",
		"Cool Control Method",
		"Cool PB",
		"Cool Reset / Integral",
		"Cool Rate / Derivative",
		"Cool Dead Band",
		"Cool Hysteresis",
		"Proportional Term",
		"Integral Term",
		"Derivative Term",
		"Ramp Rate";

$ End of Programming page, start of Factory page

	Param1402=
		"No",
		"Yes";

	Param1403=
		"No",
		"Set 1",
		"Set 2";

	Param1404=
		"No",
		"Set 1",
		"Set 2";

	Param1405=
		"No",
		"Yes";

	Param1406=
		"None",
		"DC / Open Collector",
		"Mechanical Relay",
		"Solid-State Relay",
		"Process",
		"Communications";

	Param1407=
		"None",
		"DC / Open Collector",
		"Mechanical Relay",
		"Solid-State Relay",
		"Process",
		"Communications";

$ End of Factory page, start of Home page

	Param1507=
		"None",
		"Alarm";

	Param1508=
		"None",
		"Alarm";

	Param1509=
		"None",
		"Alarm";

	Param1510=
		"None",
		"Alarm";

	Param1511=
		"No",
		"Yes";

	Param1512=
		"No",
		"Yes";

$ End of Home page

$ NOTE:  The following parameters MUST remain last in order for ADR to work properly!
	Param1999=
		"Disable",
		"Enable";

[Groups]

	Group1=
		"Home Page", 12,
		1500, 1501, 1502, 1503, 1504,       1506, 1507, 1508, 1509,
		1510, 1511, 1512;

	Group2=
		"Operations Page", 32,
		1200, 1201, 1202, 1203, 1204, 1205, 1206, 1207, 1208, 1209,
		1210, 1211, 1212, 1213, 1214, 1215, 1216, 1217, 1218, 1219,
		1220, 1221, 1222, 1223, 1224, 1225, 1226, 1227, 1228, 1229,
		1230, 1231;

	Group3=
		"Setup Page", 76,
		1100, 1101, 1102, 1103, 1104, 1105, 1106, 1107, 1108, 1109,
		1110, 1111, 1112, 1113, 1114, 1115, 1116, 1117, 1118, 1119,
		1120, 1121, 1122, 1123, 1124, 1125, 1126, 1127, 1128, 1129,
		1130, 1131, 1132, 1133, 1134, 1135, 1136, 1137, 1138, 1139,
		1140, 1141, 1142, 1143, 1144, 1145, 1146, 1147, 1148, 1149,
		1150, 1151, 1152, 1153, 1154, 1155, 1156, 1157, 1158, 1159,
		1160, 1161, 1162, 1163, 1164, 1165, 1166, 1167, 1168, 1169,
		1170, 1171, 1172, 1173, 1174, 1175;

	Group4=
		"Programming Page", 20,
		1300, 1301, 1302, 1303, 1304, 1305, 1306, 1307, 1308, 1309,
		1310, 1311, 1312, 1313, 1314, 1315, 1316, 1317, 1318, 1319;

	Group5=
		"Factory Page", 13,
		1400, 1401, 1402, 1403, 1404, 1405, 1406, 1407, 1408, 1409,
		1410, 1411,       1413;

	Group6=
		"Non User-Interface", 2,
		1001, 1999;